Results 1 to 9 of 9

Thread: 4.6 problem

  1. #1
    Junior Member
    Join Date
    Oct 2008
    Location
    georgia
    Posts
    1

    Question 4.6 problem

    i have a 2000 gt my motor is making a knocking noise from the bottom end it has 135000 miles on it i was wondering if it would be easier t swap ot the motor or repair the problem i think it is rod or something please advise i was wonderig if a crwn vic motor was the same

  2. #2
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    You have pull it and see what the problem is first. With that mileage a rebuild is probably necessary. Not sure about the crown vic.
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  3. #3
    Senior Member Ruckus46gt's Avatar
    Join Date
    Sep 2007
    Location
    Luke AFB
    Posts
    903
    thing about modular motors is everything is interchangable basically. The difference between the models are basically material of block, and heads intake. That is why you can make a 2v a 4v etc. Have to look into what little parts you need to also change though thats were everything starts to add up

  4. #4
    Member D3VST8R96GT's Avatar
    Join Date
    Mar 2009
    Location
    Mesa/Fort sill, OK/kabul
    Posts
    58
    for the crown vic....depends on the year ....some come with 4 bolt mains ..others have variations ...that what i've read

    if your not gonna run boost or anything its shouldnt concern you to much i guess
    Last edited by D3VST8R96GT; 03-29-09 at 04:42 PM. Reason: im retarded
    I smacked my head into the handle bar the handle, bars, the handle bars.....

  5. #5
    Junior Member Boosted46's Avatar
    Join Date
    Mar 2009
    Location
    Des Moines, IA
    Posts
    13
    The troubles you'll run into are small and annoying but not impossible to overcome. I believe the intake/tb for a crown vic is on the drivers side so you'll need to reuse your top end pieces. The belt accessories and oil pan are likely different as well. The longblock itself should be a direct replacement though. You will want to take note of the flywheel bolt pattern too. Not sure if you're reusing your clutch but it will either have a 6 or 8 bolt pattern. I believe vics had romeo motors though so it likely has a 6 bolt... Hope this helps some

  6. #6
    Senior Member WildBill's Avatar
    Join Date
    Mar 2009
    Location
    Phoenix, DFW or a trailer at the track
    Posts
    944
    Quote Originally Posted by daddybadguys View Post
    i have a 2000 gt my motor is making a knocking noise from the bottom end it has 135000 miles on it i was wondering if it would be easier t swap ot the motor or repair the problem i think it is rod or something please advise i was wonderig if a crwn vic motor was the same
    It shouldn't matter, but your engine in your GT is prolly a Windsor, not a Romeo. I have no Idea if Windsor modmotors were ever put in crown vics.
    WILD BILL
    PRO-AMERICAN

    TorchRed 2003 MACH1 (Louise)
    "I remember my fallen brothers so that they may live on."
    ΜΟΛΩΝ ΛΑΒΕ

  7. #7
    Senior Member Mr. Austin's Avatar
    Join Date
    Apr 2008
    Location
    Peoria
    Posts
    1,622
    just did this to my motor and ill give you a straight up answer that no one is really givin. if its a higher pitched sound its your top end like a tick or knocking if its your lower end it will be making a more clunk sound. the clunk at that many mile would be you barrings. a high pitch would be like a push rod. thats like a ticking. and knocking would be a lifter. ticking also could be coming from an exhaust leak. all depend on the sound. what pitch. what velocity. and the strength of the sound... no one can really tell you what it is for sure over email. you would need to meet up with someone and allow them to listen. like i said. i JUST went through this with a 40 year old motor. these are the "common" things that it could be... Hope it helps a little.

  8. #8
    Senior Member fazm's Avatar
    Join Date
    Nov 2006
    Location
    gilbert, AZ
    Posts
    1,028
    Platinum Award 
    if the noise is a pushrod thats definately a prob since he dont have any :)


    as far as rebuilding it vs. putting in a used motor. putting in a used motor is probably easier/cheaper
    2005 v6 redfire mustang. yup its slow.
    12.03 @ 118.5 best et
    12.11 @ 122.0 best mph

  9. #9
    Senior Member Mr. Austin's Avatar
    Join Date
    Apr 2008
    Location
    Peoria
    Posts
    1,622
    oh sorry thats true (ahahaha). sorry im still in the old car mind frame... (im kicking my self about now)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •