Complete TH-400 Install Information --- Click Here
Well the conversion is under way
(JW The Wheel) flex plate
Get flexplate bolts from an Auto Mach 1 as the six speed flywheel bolts are too long.
My trans B&M Hi-Tek Trans Cooler.
Mounted in the Drivers Sider Fender.
Thermostat Activated Fan, but I am going to wire it to run all the time.
Results 1 to 10 of 146
-
01-30-09, 11:07 PM #1Administrator
- Join Date
- Dec 2005
- Location
- Pittsburgh, PA
- Posts
- 8,619
2003/2004 Mustang Cobra Turbo 400 / TH-400 Swap / Conversion
Sold
2004 Cobra, Whipple ,TH-400
Burning Corn
9.97 - 135.5
-
01-31-09, 01:50 AM #2Member
- Join Date
- Jun 2008
- Location
- Dover
- Posts
- 98
Very nice.
1988 GT (BBK 1 5/8th ceramic shorties, BBK O/R X Pipe, SLP LM1 Catback, MSD Blaster Coil II, MSD Pro Billet Distributor, K&N Panel Filter, Weight Reduction, MT ET Streets )
-
01-31-09, 08:22 AM #3Senior Member
- Join Date
- May 2008
- Location
- Chandler, AZ
- Posts
- 592
Very Nice! How long is the conversion going to take?
2004 Saleen Convertible #298 SC/281-SOLD
1970 Chevelle LS3 Build/T56
-
01-31-09, 09:31 AM #4Administrator
- Join Date
- Dec 2005
- Location
- Pittsburgh, PA
- Posts
- 8,619
Hope to have everything done is a few weeks.
Originally Posted by AZSaleen04
Sold
2004 Cobra, Whipple ,TH-400
Burning Corn
9.97 - 135.5
-
01-31-09, 10:23 AM #5Senior Member
- Join Date
- Apr 2008
- Location
- Phoenix
- Posts
- 390
I want to see the first pass! what are you hoping for?
2003 SRT4 12.29@109.36 SOLD
2003 Cobra 12.00@119 SOLD
2004 Cobra vert 12.05@118
-intake, exhaust, pulley
2007 Mustang GT 13.66@102
-JLT CAI
-Bama tune
-JBA axle back
-
01-31-09, 10:50 AM #6Administrator
- Join Date
- Dec 2005
- Location
- Pittsburgh, PA
- Posts
- 8,619
It should go a high 9 if all works well. Originally Posted by silvrsvt
Sold
2004 Cobra, Whipple ,TH-400
Burning Corn
9.97 - 135.5
-
01-31-09, 11:51 AM #7Senior Member
- Join Date
- May 2008
- Location
- Chandler, AZ
- Posts
- 592
Nice!
2004 Saleen Convertible #298 SC/281-SOLD
1970 Chevelle LS3 Build/T56
-
01-31-09, 04:12 PM #8Senior Member
- Join Date
- Aug 2007
- Location
- QC/Gilbert
- Posts
- 1,405
Originally Posted by BurnTire
You going before it gets hot this year? Definately need to be there for that.
-
01-31-09, 10:47 PM #9Administrator
- Join Date
- Dec 2005
- Location
- Pittsburgh, PA
- Posts
- 8,619
B&M Pro Ratchet Shifter.
Carbon Fiber Console kit.
Six speed boot will go around the shifter when complete.
Line Lock on the Right Switch
Trans brake in the hole for the left switch.
I trimmed a few edges on the shifter to fit the console plate better.
You have to cut some of the tunnel for the shift cable to pass thru.
Delete Panel
When all is done I will fill the shifter cable hole with some adhesive and insulation.
Sold
2004 Cobra, Whipple ,TH-400
Burning Corn
9.97 - 135.5
-
02-01-09, 12:42 AM #10Senior Member
- Join Date
- Aug 2007
- Location
- QC/Gilbert
- Posts
- 1,405
Great progress. What fills the area where the old shifter was?
Reply With Quote
