I know its a long shot but does anyone have a 03-04 Cobra Drive shaft laying around?
Results 1 to 10 of 12
Thread: I need a Cobra Drive Shaft
-
08-29-08, 05:21 PM #1Senior Member
- Join Date
- Aug 2007
- Location
- QC/Gilbert
- Posts
- 1,405
I need a Cobra Drive Shaft
-
08-29-08, 06:38 PM #2Administrator
- Join Date
- Dec 2005
- Location
- Pittsburgh, PA
- Posts
- 8,619
I just happen to have one in the garage.
It does not have the tranny yoke.
Went 10's LOL.Sold
2004 Cobra, Whipple ,TH-400
Burning Corn
9.97 - 135.5
-
08-29-08, 07:37 PM #3Senior Member
- Join Date
- Aug 2007
- Location
- QC/Gilbert
- Posts
- 1,405
Let me clarify my request......I need a Drive shaft that is not twisted all to heck!
-
08-29-08, 07:49 PM #4Administrator
- Join Date
- Dec 2005
- Location
- Pittsburgh, PA
- Posts
- 8,619
The drive shaft is not twisted and was fine when I took it off the car.
Originally Posted by wickedcobra
Let me clarify my request......I need a Drive shaft that is not twisted all to heck!
I got a longer shaft to increase the yoke engagement area.
If the shaft was junk I would throw it out.
I do have the old yoke but being it was involved in the output shaft damage I would not recommend using it.Sold
2004 Cobra, Whipple ,TH-400
Burning Corn
9.97 - 135.5
-
09-14-08, 09:38 PM #5Junior Member
- Join Date
- Sep 2008
- Location
- Mt. Juliet, TN
- Posts
- 9
cobra driveshaft
hey jeff, do you still have that driveshaft laying around? I may be interested. I know I am new here, but this post is how I found this forum. I've got a 95 and I am doing a t-56 swap and needing a driveshaft. How much for it and to ship to 37122? I don't need the front yoke. thanks
boss 331
-
09-24-08, 01:35 AM #6Senior Member
- Join Date
- Apr 2006
- Location
- North Phoenix
- Posts
- 4,184
soo...anyone else got one layin around? found out while doing a ujoint swap that mine is peaced out...
-
09-24-08, 04:42 AM #7Senior Member
- Join Date
- Aug 2007
- Location
- QC/Gilbert
- Posts
- 1,405
good luck Tony! nobody has one around. Just order one from dynotech. about $400 bucks. I can get you a new one from ford for just over $300 at employee cost
-
09-24-08, 10:19 AM #8Senior Member
- Join Date
- Apr 2006
- Location
- North Phoenix
- Posts
- 4,184
yeah, thinking about just throwing the stock shaft back in there. its worked till now. the only issue was the ujoint end caps just falling out when i pulled the clips. doh!
-
09-24-08, 12:13 PM #9Administrator
- Join Date
- Dec 2005
- Location
- Pittsburgh, PA
- Posts
- 8,619
What length did you get? Originally Posted by wickedcobra
Sold
2004 Cobra, Whipple ,TH-400
Burning Corn
9.97 - 135.5
-
09-24-08, 03:43 PM #10Senior Member
- Join Date
- Apr 2006
- Location
- North Phoenix
- Posts
- 4,184
was gonna send ya apm, but says you can't get them. weird. Originally Posted by wickedcobra
think i am gonna go this route. but i hit up sanderson, and they did not have one, and it looks like no one in town has em, new or used. how long would it take you to get it? sanderson quoted me like 340 for it.
thanks man.
