Page 1 of 2 12 LastLast
Results 1 to 10 of 15

Thread: Brakes Squealing

Hybrid View

  1. #1
    Senior Member IMSHAKN's Avatar
    Join Date
    Nov 2007
    Location
    Gilbert
    Posts
    726
    Silver Award 

    Brakes Squealing

    My rear brakes are still squealing after replacing some badly worn pads. It looks to be like maybe there may be a problem with the piston itself because the problem is isolated to the rear drivers side. I'm positive this is the only trouble spot because there are some slight grooves that have formed and the outer pad does not appear to sit right on the caliper after driving it around for a while. When I pulled the old pads, the top part of the pad was much more worn than the bottom part of the pad indicating that the pad is not seating in there properly, which is what I think is going on once again.

    So the question is, what could be causing this?
    ~Andrew

  2. #2
    Senior Member jjmatheson's Avatar
    Join Date
    Feb 2008
    Location
    Glendale
    Posts
    201
    Stupid question, did you turn the rotors? If you did check to see if the guides move freely, the top guide could be frozen. Are you lubricating the part where the pads slide on the caliper bracket? Make sure that part has not worn out and is keeping the pads from moving freely If so replace the hardware. I hope this makes sense, and I'm not trying to insult your intelligence. Good luck.

  3. #3
    Senior Member IMSHAKN's Avatar
    Join Date
    Nov 2007
    Location
    Gilbert
    Posts
    726
    Silver Award 
    Did not turn the rotors. I usually do not turn rotors with less than 20k on them (Current ones are from Baer with less than 10k on them). I'm going to take the caliper apart again and go through everything throughly. I'm almost wondering if the piston is sticking because I did not have to turn the drivers side piston back into the caliper nearly as much as I had to turn the passenger's side. I will take a look at what you did mention though. The more things to look at, the better.
    ~Andrew

  4. #4
    Member sesso's Avatar
    Join Date
    Feb 2008
    Location
    Tempe, AZ
    Posts
    72
    Thats why they squeek... turn the rotors and it will be gone. your rotors are probably glazed.
    2005 GT Mustang 5 spd, Shaker 1000, Short Antenna, JBA Headers, JBA O/R X pipe, BBK TB 62mm, C&L CAI, Diablosport tune, BMR LC Arms, Pro 5.0 Shifter, ZEX Nitrous 125 Shot, 4.10s.Coming soon: cams or 5.4 swap

  5. #5
    Senior Member IMSHAKN's Avatar
    Join Date
    Nov 2007
    Location
    Gilbert
    Posts
    726
    Silver Award 
    I'll have that done then, though what concerns me most is the way the pad seems to sit in the caliper itself. It's almost as if the metal edge of just the drivers side caliper is sitting much too close to the rotor surface. Should I have the rotors turned on a on-car lathe or take them off and have some shop do them?
    ~Andrew

  6. #6
    Senior Member jjmatheson's Avatar
    Join Date
    Feb 2008
    Location
    Glendale
    Posts
    201
    Yep, the new pads need to seat with the rotors, and no that makes no difference how far you pushed the piston back as long as the caliper goes back on. The piston is going to come out as soon as you hit the brake pedal.

  7. #7
    Senior Member IMSHAKN's Avatar
    Join Date
    Nov 2007
    Location
    Gilbert
    Posts
    726
    Silver Award 
    Quote Originally Posted by jjmatheson View Post
    Yep, the new pads need to seat with the rotors, and no that makes no difference how far you pushed the piston back as long as the caliper goes back on. The piston is going to come out as soon as you hit the brake pedal.
    Only reason why I mentioned that was I have a feeling that maybe the piston is sticking, though I'm not a tech so I can't be sure. I think I'm going to lube the piston up really well and try again. Then I'll probably just have the car dropped off at Berge and have them take a look at it since I get a good discount there. This one is a little outside of my experience. I know how to replace pads, rotors, service calipers, drums, replace calipers and all that good stuff, but the diagnostic end is my weak spot.
    ~Andrew

  8. #8
    Senior Member jjmatheson's Avatar
    Join Date
    Feb 2008
    Location
    Glendale
    Posts
    201
    Well on car lathe is the best, just do what is available to you, Its just the rear brakes.

  9. #9
    Senior Member jjmatheson's Avatar
    Join Date
    Feb 2008
    Location
    Glendale
    Posts
    201
    Yeah you cant lube the piston its sealed. If you want help I would be more tha happy to give you a hand just bring it over. I am a tech no worrys. Let me know. Jeremy

  10. #10
    Member sesso's Avatar
    Join Date
    Feb 2008
    Location
    Tempe, AZ
    Posts
    72
    If the piston is sticking the piston side will wear faster. take them off and have them cut on a lathe.
    2005 GT Mustang 5 spd, Shaker 1000, Short Antenna, JBA Headers, JBA O/R X pipe, BBK TB 62mm, C&L CAI, Diablosport tune, BMR LC Arms, Pro 5.0 Shifter, ZEX Nitrous 125 Shot, 4.10s.Coming soon: cams or 5.4 swap

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •