Results 1 to 9 of 9

Thread: Detailing the engine

  1. #1
    Senior Member
    Join Date
    Aug 2006
    Location
    Florida
    Posts
    1,879
    Gold Award 

    Detailing the engine

    I was hoping someone could help me out, I want to buy some detailing stuff for the engine, IE hoses etc.. Something that will protect the aweful drying out. I was told once but forgot what it was. Any information would be great. I need to get some stuff before the show, Thanks bunches T

  2. #2
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    I hit my engine with simple green clean.

    Then use a light water mist to clean it off.

    Then Spray Tire Foam on anything that is rubber or plastic for the shine.

    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  3. #3
    Member 06BlackGT's Avatar
    Join Date
    Jan 2007
    Location
    California, AGAIN
    Posts
    32
    When applying water to the engine do you have to cover anything up to protect it from the water? Or by using light misting pressure not hurt anything

  4. #4
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    Quote Originally Posted by 06BlackGT View Post
    When applying water to the engine do you have to cover anything up to protect it from the water? Or by using light misting pressure not hurt anything
    The Light Mist will not hurt anything. You obvoiusly don't want to get the airfilter wet.
    I also use the air gun to blow all the water off after I mist it.
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  5. #5
    Senior Member 50 BMG's Avatar
    Join Date
    Dec 2005
    Location
    AZ
    Posts
    770
    Gold Award 
    I use F-21. I very, very rarely spray anything onto my car (then again it's only been water washed twice). I spray it on the rag/shammy then wipe.

  6. #6
    Senior Member Olivas's Avatar
    Join Date
    Jun 2006
    Location
    Denver, CO
    Posts
    120
    Watch the Simple Green on the aluminum. Discussion about it over here: http://www.mach1registry.org/forums/...ad.php?t=57271

    I know that cobra's have a cast iron block but the heads are still aluminum. The mach engines are all aluminum, and I believe the '05 and up motors are as well.
    2003 Azure Blue Mach 1
    IUP - 5spd
    18" Black Saleen Rims
    245/40/18 Front 285/35/18 Rear
    Bassani Catted X-pipe
    Borla Cat Back
    C&L CAI
    PHP Spacer
    Meziere Electric Water Pump
    FRPP Aluminum Driveshaft

    MGW Orange Shifter
    Steeda 3 pt Strut Tower Brace
    MM Full Length Subframes
    MM Chrome C/C Plates
    MM Lower Control Arms
    H&R Race Springs
    Variuos MGW Interior Pieces

  7. #7
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    I never really hit the motor with the simple green. It is usually just around the firewall. the rest is just a light mist of water and air gun.
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  8. #8
    Junior Member 2000shadowstang's Avatar
    Join Date
    Nov 2006
    Location
    Phoenix, Az
    Posts
    20

    Detailing my car

    Does anyone know of a very good repututable engine detailer in the SW Valley..I am sure this was mentioned before.

    I really like to get this done for the show on Sat

    Thanks

    2000 Mustang GT

  9. #9
    Junior Member
    Join Date
    Apr 2007
    Posts
    2
    Basically, I use a dilute solution of Simple Green in a spray bottle to keep my engine bay clean. Everytime I wash my car I use it under the hood. Just spray it on and wipe it off and it seems to keep it all very clean.
    Attached Images Attached Images   

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •