Page 1 of 2 12 LastLast
Results 1 to 10 of 18

Thread: My 02 GT won't start, need help.

  1. #1
    Member JustaGT's Avatar
    Join Date
    Apr 2011
    Location
    San Tan Valley, Az
    Posts
    33

    My 02 GT won't start, need help.

    Ok here's the rundown, alternator went out on me about a week ago so I bought a replacement from Americanmuscle.com. Drove fine until battery drained so I went and charged it, got it back in the car, no problem. First time I take the car out it felt sluggish, like really sluggish. The it dies on me at a light, so I start it back up and it does it again at the next light and the only way I can keep it on at stop lights is feathering the gas while on the break and finally it dies, can't restart it, can't be jumped, nothing. Tow it home, plug in my Diablo and also the diagnostics you can bring up while holding down the odo button while turning the ignition on, both indicate a PATS issue (codes 9600 and 9602), so I take it to my local Ford and tell them what I came up with so far and check everything out. They tell me they read no codes and told me something is mechanically locking my motor up and they tried to turn my crank pulley with a breaker bar and it didn't budge and that it would cost me at least $300 to start checking out stuff starting with dropping my oil pan so I decide to tow my car back home because I can drop my oil pan for far less than $300. So now I have my car back, batteries drained, Ford said they read no PATS codes which is odd because as soon as I got my keys back and checked the PATS codes were still there and I was able to turn my crank pulley 1/4 of a turn in each direction with my breaker bar so now I'm confused and dunno what to check next. Any ideas?
    ____________________________________


    The car has been stuck in my garage and I don't know if pulling everything apart is neccessary yet. Any advice would be greatly appreciated.

  2. #2
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    Pull the alternator and battery and have them tested. Are you absolutely sure everything is hooked up correctly?

    Could be the battery.
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  3. #3
    Senior Member SloSVO's Avatar
    Join Date
    Oct 2008
    Location
    Buckeye, Az
    Posts
    586
    1/4 of a turn???.. turn that biatch at the minimum 2 full turns... also charge your battery till its fully charged.. then start again.. but do the 2 full turns first.

  4. #4
    Member JustaGT's Avatar
    Join Date
    Apr 2011
    Location
    San Tan Valley, Az
    Posts
    33
    Burntire - Yes everything's hooked up.
    SloSVO - I could only turn it that much which tells me my motor's shot b/c I know I can't get 2 full turns.

  5. #5
    Senior Member SloSVO's Avatar
    Join Date
    Oct 2008
    Location
    Buckeye, Az
    Posts
    586
    AHH.. I get it.. the way I read it was that you only turned it 1/4 of a turn and said thats good.... sucks..

  6. #6
    Junior Member
    Join Date
    Oct 2009
    Location
    Phoenix
    Posts
    15
    check your a/c compressor - these like to lock up - make sure they (or you ) are removing the serp belt before turning over the engine. More than a few engines have been replaced to find that it was a locked up compressor. (last one was a 96 Tarus) The PATS codes can appear due to extreme battery voltage. When the batt voltage dips below 11 or so volts we start seeing weird symptoms.

  7. #7
    Senior Member Rick Shopmier's Avatar
    Join Date
    Apr 2008
    Location
    Grand Junction, CO
    Posts
    343
    Back to the beginning. Did you have the original alternator checked to be sure it failed? If yes why not purchase one locally so if there is a problem with it you can return it (Partsmart is a good suggestion). Next you said you drove till the battery was drained, golly gee do you think the alternator you put on was bad or did you not properly hook it up, more the latter since the battery issue and maybe the problem with power loss (electric fuel pump not getting enough juice to run). I do not know where the locked up motor came from since it seems the engine stalled (you did not indicate any odd noise when it quit) and won't restart (cranked right?). Quarter turn or 2 turns, indicate the motor not siezed. Your issue has moved to the electrics/electronics and to the first guy that worked on the car when this all started (some idiot, fire him). A siezed a/c compressor (you would have be able to hear this going down, like a screaching belt) give me a break (not brake). At this point you will be lucky if you did't kill the ECM or at least damage it. As the $ fly off into the ozone layer....good luck!

    RACER00

  8. #8
    Junior Member
    Join Date
    Oct 2009
    Location
    Phoenix
    Posts
    15
    If there is a concern of a possible locked up engine - remove the belt and turn it over by hand....
    as for
    Quote Originally Posted by Rick Shopmier View Post
    A siezed a/c compressor (you would have be able to hear this going down, like a screaching belt) give me a break (not brake).
    A seized a/c compressor can and will stop a starter from starting an engine - have SEEN IT many many times. So....easy test - pull the belt off and turn it over. if it moves - great - if not - proceed to tear down. Put a known good battery on the vehicle and pull some codes- unless it was jumped backwards (and even then) it is very unlikely that you fried your ECM.

  9. #9
    Junior Member
    Join Date
    Oct 2009
    Location
    Phoenix
    Posts
    15
    Also - Ford doesnt use codes 9600 and 9602 - There is a B1600 and a B1602 - which is related to the transponder not being read or a partial read. FYI if you are searching the webs and not finding much. The 9000 series codes may be how your tuner reads them - this I dont know.

  10. #10
    Super Moderator Jacostang's Avatar
    Join Date
    Jul 2006
    Location
    Mesa, Az
    Posts
    4,443
    Platinum Award 
    Yes, pull the belt then turn the engine over.....
    "The choices we make, dictates the lives we lead"


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •