Results 1 to 9 of 9

Thread: vibration help please!!!!!!!!!!!!!!!!

  1. #1
    Junior Member
    Join Date
    Jul 2010
    Location
    mesa
    Posts
    4

    vibration help please!!!!!!!!!!!!!!!!

    Hello i need some help or recomendations of good repair place. My 68 mustang has a bad vibration at about 65 mph. kind of goes away at 70 but comes and goes between 60 and 70. I have replaced so far shocks, transmission mount, had the wheels ballanced, and yesterday i brought original drive shaft to mesa driveshaft to balance and they informed me that the rubber seal was bad and slipping and i needed a new one. I dropped 280.00 on new one hoping that would solve and still vibrates same. What else should i check? I would like to get front looked at to rule out any issues but do not know a good place to take that wont try and rake me over. I do not think it is the rear bearings but guess could be. any ideas would be appreciated,

  2. #2
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    Do you feel the vibration in the seat of your pants or in the steering wheel?

    You could rotate the drive shaft 90 or 180 degrees depending on the type of mount you have on the rear end.
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  3. #3
    Junior Member
    Join Date
    Jul 2010
    Location
    mesa
    Posts
    4
    its a new drive shaft would that make difference? and the its had to tell where vibration is, its like whole car doors rattel, like the whole frame is shaking. so do i just disconect the drive shaft and spin it two the next two u joints?

  4. #4
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    Quote Originally Posted by katmandoo View Post
    its a new drive shaft would that make difference? and the its had to tell where vibration is, its like whole car doors rattel, like the whole frame is shaking. so do i just disconnect the drive shaft and spin it two the next two u joints?
    Yes mark the spot you have the drive shaft now then rotate it and see if it helps. Jack the car up and check for excessive play in the wheel bearings. Does the car vibrate during acceleration, cruise and deceleration at the vibration speed? Did this issue just occur all of a sudden?
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  5. #5
    Senior Member trucker's Avatar
    Join Date
    Sep 2009
    Location
    phoenix az
    Posts
    484
    I have a question for you does this car have a c4 tranny ?

  6. #6
    Junior Member
    Join Date
    Jul 2010
    Location
    mesa
    Posts
    4
    yes car has c-4 its a vibration that happens when over 60 but will stop and start, it rattles my doors the most im wondering if the door jams are to loose and rattle to easy at times? i have orginal tires and rims im going to switch out and try to see if that makes a difference,

  7. #7
    Junior Member
    Join Date
    Jul 2010
    Location
    mesa
    Posts
    4
    i put orginal rims and tires on (pizza cutters ) and drives smooth as can be. so i guess balance was a waste of money at big o tire,

  8. #8
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    Glad you got it figured out.
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  9. #9
    Senior Member 05mustangman's Avatar
    Join Date
    Jan 2007
    Location
    Surprise, AZ
    Posts
    1,197
    Nice glad it was nothing too serious!



    2010 GT500 - Modded out the Wazoo. Tuned by Shelby American Motorsports. Las Vegas, NV.
    2003 Ford Lightning- Airaid intake, Bassani exhaust, Lakewood torsion bar, 2" drop shackels and a few more mods.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •