Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Idle Issue 89 GT

Hybrid View

  1. #1
    Member 89GT's Avatar
    Join Date
    May 2010
    Location
    Surprise
    Posts
    33

    Angry Idle Issue 89 GT

    I picked my 89gt up sunday and found out that the TPS is unplugged. Let me start off that it had a surging idle it would go from almost dying to 1000rpm and sometimes it would die. I pulled the intake apart, cleaned the MAF and found the TB to be very dirty, cleaned that, and plugged the TPS in and took it for a drive. Ran excellent until I got in it the next day. Ran good until 5 min of running and the idle shoots to 2000rpm and stays there. I Pulled over and disconnected the TPS and the idle is perfect. Now, I was thinking mayb the computer needs to be reset because it has parameters set from running without a TPS signal for so long, and then plugging it back in confused the ecm... does this sound feasible? I haven't tried yet, but I plan on doing the idle re-learn procedure in the near future. TPS voltage at idle is .65, What do you think?

  2. #2
    Senior Member SloSVO's Avatar
    Join Date
    Oct 2008
    Location
    Buckeye, Az
    Posts
    586
    the tps voltage is a bit on the low side.. I shoot for .95 KOEO.. next time its stuck like that look at the Tp voltage.. you may have a shorted sensor..

  3. #3
    Member 89GT's Avatar
    Join Date
    May 2010
    Location
    Surprise
    Posts
    33
    Quote Originally Posted by SloSVO View Post
    the tps voltage is a bit on the low side.. I shoot for .95 KOEO.. next time its stuck like that look at the Tp voltage.. you may have a shorted sensor..
    I figured it was low. Articles say to shoot for .98-.99 so I will have to hollow the holes a bit more to achieve that. I got the car with the TPS disconnected, it runs good with it off, but smells rich. The IAC seems to be functioning properly. I will have a look at it this weekend more in depth. Thanks for the offer SloSVO, if I can't fix it I will take you up on the offer.

  4. #4
    Senior Member ChuckD's Avatar
    Join Date
    Jul 2006
    Location
    El Mirage
    Posts
    204
    If you wanna come by I can give you a hand crossroads are Cactus and El Mirage.
    Chuck
    VETERANS DIESEL SERVICE
    1988 LX
    1997 GT
    1997 F350 CC LWB Powerstroke
    2002 Expedition Eddie Bauer

  5. #5
    Member
    Join Date
    Jun 2007
    Location
    Queen Creek
    Posts
    65
    As long as TPS voltage is between .5 and 1v you are fine. The computer takes the baseline tps voltage reading and then subtracts the baseline value out of the current reading to determine how far the throttle is open. That's why TPS sensors aren't adjustable (you have to slot the holes to adjust). If it's not reading in the acceptable range without modifying it, then get a new one.

    This is the best trouble shooting guide I've seen for surging idle:
    http://www.stangnet.com/mustang-foru...checklist.html
    68 Hardtop
    "Kandi Taylor"

  6. #6
    Member 89GT's Avatar
    Join Date
    May 2010
    Location
    Surprise
    Posts
    33
    Thank you!

  7. #7
    Member
    Join Date
    Jun 2007
    Location
    Queen Creek
    Posts
    65
    Let us know how it turns out
    68 Hardtop
    "Kandi Taylor"

  8. #8
    Member 89GT's Avatar
    Join Date
    May 2010
    Location
    Surprise
    Posts
    33
    Quote Originally Posted by 1tuff68 View Post
    Let us know how it turns out
    Ok, I disconnected the battery, connected the TPS back up, and started it up, ran good for maybe 5 min, then rpms creeped to 2000rpm... I can disconnect the TPS and it runs fine. I think I am going to try a new TPS.

    Joe

  9. #9
    Member 89GT's Avatar
    Join Date
    May 2010
    Location
    Surprise
    Posts
    33
    Installed a new TPS and it has .97 volts now. But when I connect the IAC back up it starts running really erratic, it surges alot and stalls. I think the next step is going to be the IAC itself.
    89 Gt
    E303 cam (I think)
    Sub-frame connectors
    I think it has a port job
    Might be re-geared
    Set up for nitrous (police removed it)
    Give me a break, it was from an impound lot, It's quick that is all I know.

  10. #10
    Member 89GT's Avatar
    Join Date
    May 2010
    Location
    Surprise
    Posts
    33
    I cleaned the IAC too, looked like fresh oil on it, Maybe the engine has excessive blowby... It ran good for 2 min of driving then ran like crap.. Runs great with the IAC disconnected..
    89 Gt
    E303 cam (I think)
    Sub-frame connectors
    I think it has a port job
    Might be re-geared
    Set up for nitrous (police removed it)
    Give me a break, it was from an impound lot, It's quick that is all I know.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •