Page 3 of 3 FirstFirst 123
Results 21 to 29 of 29

Thread: Clutch and Roll Cage Project Cliff Note Version

  1. #21
    Junior Member autoxstang's Avatar
    Join Date
    Mar 2007
    Location
    Savannah, GA
    Posts
    27
    Well now that you have the cage and bell housing installed, how fast can you go before you have to add something else?

    2004 Redfire Cobra, #583/3768, Born 11/26/03
    2.8 KB numbers coming soon....

  2. #22
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    Quote Originally Posted by autoxstang View Post
    Well now that you have the cage and bell housing installed, how fast can you go before you have to add something else?
    Well I am going to upgrade my Level 5's to STOCK half-shafts next so the car is drivable. LOL
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  3. #23
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619

    Seats Are In

    I installed my Corbeau TRS seats today.

    These were the only nice seats that I could find that clears the swing out. I got the crotch strap cut out also. I really liked the stockers, but I feel they were not the safest setup for a 5 point harness.

    Install should have been easy but I always have bad luck.
    Seats got delivered to the neighbors across the street so the bad luck begins.
    Drivers slider was catching on some of the seat material when sliding the seat all the way forward. A little velcro did the trick.
    Next I notice a ball bearing in the back seat. Pull the seat out and find where it goes and put it back in the slider.
    Put the seat back in a notice the eye bolt in the tunnel for my harness is rubbing the seat and now 2 ball bearings feel out. WTF

    Pull the damn seat out again. Put the bearings back in and use a punch to make sure the damn things don't fall out again.
    Put the seat back in and strip the threads in the floor on the right rear seat bolt. Luckily there is a nut on the bottom for the subs, but I will re thread that another day.

    Move the eye bolt. Seal the old hole.

    Go to put the nuts on the underside of the car where the boltd come thru the sub frame connectors and now the stock bolts are too short because the seat bracket is thicker.

    Off to Home Depot. Of course all the grade 8 stuff isn't in the right section and 20 minute later I find everything I need.

    Come home and put the bolts in and don't break anything

    After that multi hour fiasco I start on the passenger side. 10 minutes later I was done. LOL

    Well the final product is nice. The seats are a little lower than the stockers which is good for me.
    Attached Images Attached Images   
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  4. #24
    Senior Member ASUSMC's Avatar
    Join Date
    Sep 2006
    Location
    Phoenix
    Posts
    1,663
    Them there is some nice seats. You are keeping the stockers I assume?
    2012 Race Red GT w/ a 5 Liter and a 6 speed
    2010 Dodge Challenger R/T traded in.
    '03 DBS Cobra .... Traded in, THANK GOD
    '01 Ford Lightning.... Sold, sorely missed

  5. #25
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    Quote Originally Posted by ASUSMC View Post
    Them there is some nice seats. You are keeping the stockers I assume?
    I haven't decided yet. My stockers have the dark inserts. The ones everyone wants. I may sell them. I may throw the fronts on the wifes GT. I hate those GT seats. They are way too high.
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  6. #26
    Senior Member P Machy's Avatar
    Join Date
    Jul 2006
    Location
    So Cal
    Posts
    248
    LOL...the modding gods are saying " STOP MODDING ALREADY " .

    Nice seats. How much did you get them for? GT = Mach1 seat...they suck! Love the Termee seats.

  7. #27
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    Quote Originally Posted by P Machy View Post
    LOL...the modding gods are saying " STOP MODDING ALREADY " .

    Nice seats. How much did you get them for? GT = Mach1 seat...they suck! Love the Termee seats.
    I think it was about $1000 for everything shipped.

    I really like the stock seats also, but they are not safe to use with a 5 point harness setup.

    Ok I will stop modding until the fall. LOL
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

  8. #28
    Senior Member P Machy's Avatar
    Join Date
    Jul 2006
    Location
    So Cal
    Posts
    248
    So how close do these seat feel to a Termee seat?


    Ohh, what was the weight savings like?

    I cant stand how the Mach1 seat feel after a year in the Termee...hugh difference!

  9. #29
    Administrator BurnTire's Avatar
    Join Date
    Dec 2005
    Location
    Pittsburgh, PA
    Posts
    8,619
    Quote Originally Posted by P Machy View Post
    So how close do these seat feel to a Termee seat?


    Ohh, what was the weight savings like?

    I cant stand how the Mach1 seat feel after a year in the Termee...hugh difference!
    They feel different. They sit a little lower. Saved about 27 lbs total.
    Stockers are more comfortable IMO.
    Sold
    2004 Cobra, Whipple ,TH-400
    Burning Corn
    9.97 - 135.5

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •