with a shitty 1.96 60ft I went 12.05 @ 118mph no nitrousso I think I am going to try and put the cage in this week so I can go out again next week and try for that 11 second slip!
Results 1 to 10 of 18
Thread: Got the boot at speedworld
-
01-10-10, 11:05 AM #1Senior Member
- Join Date
- Apr 2008
- Location
- Phoenix
- Posts
- 390
Got the boot at speedworld
2003 SRT4 12.29@109.36 SOLD
2003 Cobra 12.00@119 SOLD
2004 Cobra vert 12.05@118
-intake, exhaust, pulley
2007 Mustang GT 13.66@102
-JLT CAI
-Bama tune
-JBA axle back
-
01-10-10, 11:59 AM #2Senior Member
- Join Date
- Oct 2008
- Location
- Buckeye, Az
- Posts
- 586
which cage you getting? MM or custom?
-
01-10-10, 02:15 PM #3Senior Member
- Join Date
- Nov 2008
- Location
- Phoenix
- Posts
- 175
the track sucked last night ,,,,but good run i ran after u with a 12.05 @116 w/2.0 60 ft ...
03 motor w/stage 3 cams ,JLT c.a.i,BBK o/r X pipe,Tri-Ax,C.C U/L flywheel ,
Competition Clutch, I.R.S 31 spline w/4:10's,SCT tuner,Eibach sport line,tokico, .....
NEW set up
S/C 17psi 462HP 505TQ....
11.76@116 1.63 60ft.
-
01-10-10, 05:27 PM #4Senior Member
- Join Date
- Nov 2006
- Location
- Scottsdale
- Posts
- 750
Nice!
2011 Shelby GT 500
Black/Black/Satin Black Stripes, Electronics Pkg, FRPP/BMR Suspension/Borla-Ford Racing Exhaust
488rwhp/463rwtq bone stock
Great Past Rides:
2003 Mustang Cobra SVT Convertible- 302 Stroker & more- PSR Tuned, 2003 Mustang GT- Silver Coupe w/boltons
1996 Mustang GT/SC- Paxton SC & Tons of Mods- SuperFord Mag Car, 1995 Mustang- Red w/boltons. 1968 Galaxie 500
-
01-10-10, 05:53 PM #5Senior Member
- Join Date
- Apr 2008
- Location
- Phoenix
- Posts
- 390
its a MM but its been customized. it bolts in where the back seat would be but instead I will have a rear seat delete with holes for the cage. Hopefully it will look good in there!
Originally Posted by SloSVO
ya it sucked bad! I will be there next week but not until after work, around 7 or 8 Originally Posted by az2k1
2003 SRT4 12.29@109.36 SOLD
2003 Cobra 12.00@119 SOLD
2004 Cobra vert 12.05@118
-intake, exhaust, pulley
2007 Mustang GT 13.66@102
-JLT CAI
-Bama tune
-JBA axle back
-
01-10-10, 06:09 PM #6Senior Member
- Join Date
- Oct 2008
- Location
- Buckeye, Az
- Posts
- 586
get to work buddy!!! hehe...
-
01-10-10, 07:20 PM #7Administrator
- Join Date
- Dec 2005
- Location
- Pittsburgh, PA
- Posts
- 8,619
Bolt in cross bar is not NHRA legal and will not pass tech.
Sold
2004 Cobra, Whipple ,TH-400
Burning Corn
9.97 - 135.5
-
01-10-10, 10:40 PM #8Senior Member
- Join Date
- Apr 2008
- Location
- Phoenix
- Posts
- 390
you are the 2nd person who has told me this. Last night I showed the picture to 2 different "tech's" at speedworld and they said it will pass just fine. Also the guy I bought it from used it at firebird and never had a problem.. Originally Posted by BurnTire
Should I just have the cross bar welded in?2003 SRT4 12.29@109.36 SOLD
2003 Cobra 12.00@119 SOLD
2004 Cobra vert 12.05@118
-intake, exhaust, pulley
2007 Mustang GT 13.66@102
-JLT CAI
-Bama tune
-JBA axle back
-
01-10-10, 10:49 PM #9Administrator
- Join Date
- Dec 2005
- Location
- Pittsburgh, PA
- Posts
- 8,619
NHRA General Regulations: 4:10 Roll Bars
Crossbar and rear braces must be welded to main hoop.
The tubes must be welded together. That does not mean welding it to the tabs you have.
If you plan to wrap your harnesses they must be boxed in.
Sold
2004 Cobra, Whipple ,TH-400
Burning Corn
9.97 - 135.5
-
01-11-10, 12:40 AM #10Senior Member
- Join Date
- Oct 2008
- Location
- Buckeye, Az
- Posts
- 586
mike is going around posting the final list of people that are going on the 16th... he has you as going there...silvrsvt
Reply With Quote