-
Technical Articles
by Published on 11-20-10 03:31 PM Number of Views: 24269
Parts list and considerations:
TH-400
Converter
JW SFI Flex Plate
JW SFI Bell
JW Crank Adapter
Bolts for Bell to Block
Bolts for flex plate to crank - Ford Auto Mach 1
Bolts converter to flex plate
Bolts for cross member to trans mount.
Custom Driveshaft
Dipstick
Trans Cooler
Cooler Mounting Hardware
Cooler Lines and fittings
Shifter
Center console kit if relocating shifter from stock position
Trans-brake button
Trans Temp Gauge
...by Published on 06-21-10 05:54 PM Number of Views: 19745
Maximum Motorsports M 6 Point Roll Bar Project 2004 Mustang Cobra
Well after all the talk about my project and no action I finally got started. Started the interior stripping to install the MM 6 point roll bar....
I have been weighing all the items so I will start a weight reduction thread soon.
by Published on 06-21-10 04:46 PM Number of Views: 10680
These are some photos from when I removed and installed half shafts 3 times in 2 months. Well thats a whole different story.
...by Published on 07-16-10 03:01 PM Number of Views: 14581
Well I finally got around to some more fuel system upgrades. I had a BAP set at 50 and -8 line upgrade already. Duty cycle on race gas was 95% which was pushing it to say the least. Now the BAP is no longer need with my new setup.
...by Published on 06-21-10 01:44 AM Number of Views: 9713
This is a method to make an ABS sensor to works as a speedometer sensor. This is helpful for those converting to an auto transmission. The price to make a TH-400 work in a conventional manner was several hundred dollars. That drove me to look for a more affordable solution.
...by Published on 06-21-10 04:36 PM Number of Views: 10367
How to remove the PPRV (Hesitation Creator).
The PPRV is known to cause hesitation issue between shifts in high boost applications.
...by Published on 07-16-10 02:45 PM Number of Views: 17987
MSD 2-Step Launch Control
Ford Modular Motors 1999 and On
Part Number 8734
The MSD unit pulls spark. The stock limiter pulls fuel.
...by Published on 06-21-10 03:49 PM Number of Views: 16668
This is a link on how to setup a hurst roll control kit on a cobra.
I have this setup and it works great.
http://www.joelynch.org/cobrasite/Jo...line-lock.html
Installing Line Lock
These notes apply specifically to a 99 Cobra with ABS. A Mustang GT and other new cars, at least through the 2001 model year, ...by Published on 06-22-10 12:28 PM Number of Views: 14218
Well I have seen questions from time to time about adding race gas without tuning which can be a very expensive experiment. I am going to explain how stoich effects AFR. Hopefully in simple format.
I am not going to get into MAF transfer functions or other tuning functions.This is just about fuel.
First lets define a few terms:
AFR: Air Fuel Ratio
Stoich Rating: In simple terms is the AFR to have chemically complete combustion that is neither rich or lean. For Example most pump gasoline is about 14.64 to 1. Which means 14.7 ...by Published on 10-12-10 12:30 PM Number of Views: 13996
Attached is a writeup from LTZ MACH on how to take install full manual control switches to your intercooler pump and high speed fan both under the hood and in the interior.
...by Published on 06-21-10 03:51 PM Number of Views: 16069
99-04 Mustang HID Install
By Tony Nesbitt
This is a write up for the install of an hid kit on a 99-04 ...by Published on 12-05-10 04:25 PM Number of Views: 32151
Here is how I change the engine oil on my 2007 GT500. Although the details (oil type & quantity, drain plug torque, ...by Published on 01-08-11 01:45 PM Number of Views: 30901
Ford's normal maintenance schedule says you should replace the cabin filter every 15,000 miles or as required for special ...by Published on 02-26-14 04:06 PM
Well I came up with the The number of turns head thread Test.
Basically there is a seat in the head for the wider portion of the plugs just above the threads to stop on. This seat, notch, ledge, whatever ...
