PDA

View Full Version : The transformation has begun !!


wickedcobra
11-07-07, 06:52 PM
Ok, Im doing the solid axle with some other goodies.

-8.8 Ford racing housing
-3.73s with trac loc diff
-31 spline axles
-UPR upper and lower Control arms (adjustable)
-Spherical bushings so no swaybar needed
-not sure on exhaust yet
-MM wheel spacers
-Tokico D-specs

While I was at it I decided to do some work to the front

-Tokico D specs
-MM CC plates
-MM coil over kit
-Wheel bearing (was bad)

It has been fun thus far. Check out my new License plate too.

http://img211.imageshack.us/img211/2228/newpics025oh0.jpg (http://imageshack.us)

http://img149.imageshack.us/img149/539/newpics024jz9.jpg (http://imageshack.us)

http://img149.imageshack.us/img149/539/newpics024jz9.jpg

http://img149.imageshack.us/img149/5867/newpics021ko8.jpg (http://imageshack.us)

http://img66.imageshack.us/img66/3350/newpics020by3.jpg (http://imageshack.us)
93mustank
11-07-07, 06:59 PM
nice....wheres all your tools
wickedcobra
11-07-07, 07:11 PM
All cleaned up and in the tool box where they belong....:veryhappy:
93mustank
11-07-07, 07:12 PM
Going to clean my garage as we speak.......
BurnTire
11-07-07, 07:13 PM
Looks fun!
AZSonicSnake
11-07-07, 07:24 PM
dang, that looks like alot of fun!
wickedcobra
11-07-07, 11:29 PM
It is but I am ready to finish up so I can drive it.....
AZSonicSnake
11-07-07, 11:31 PM
trust me, i know that feeling well! especially when it took me 3-4 days to get all the stuff done with my ported s/c.
silver03cobra
11-08-07, 02:17 AM
are you parting out your IRS????
wickedcobra
11-08-07, 08:41 AM
are you parting out your IRS????

No not yet.trying to sell it as a whole. If I end up parting it out I will save the piece you need.
silver03cobra
11-08-07, 10:55 AM
thanks!:twothumbsup:
vicious781
11-09-07, 03:29 AM
Poor seth!
silver03cobra
11-13-07, 12:55 AM
did you sell it? cause your the only guy with one that is getting rid of it.... oh and that responds! NO ONE LOOKS AT THREADS! (ON SVTP)
wickedcobra
11-13-07, 01:26 AM
Yeah, its gone. Sorry I forgot to let you know. My step dad works for Ford. Maybe we can get you one from there at employee cost.
Black96SVT
11-13-07, 09:19 AM
wow! looks like its coming along great, got your hands full! haha
To run the coil overs on the D Specs did you have to mod the strut or does MM make a kit that fits ?
wickedcobra
11-13-07, 03:31 PM
I had to break off the flange on the strut, Kinda sucked. Had to grind down the 3 tack welds then use some touch up paint to doctor it up a little. All in all it wasn't to bad. Would have been nice not to have to do that given those D specs aren't cheap.
Black96SVT
11-13-07, 03:44 PM
Yeah thats what I was told I would have to do. It scares me quite a bit, especially if I mess up I am out a strut
silver03cobra
11-13-07, 06:12 PM
Yeah, its gone. Sorry I forgot to let you know. My step dad works for Ford. Maybe we can get you one from there at employee cost.

any luck?