BurnTire
09-13-07, 06:52 PM
These are some photos from when I removed and installed half shafts 3 times in 2 months. Well thats a whole different story.
Put the rear of the car on jack stands and remove the wheels.
Take the e brake off
35MM Axle socket from autozone.
Remove the nut.
http://www.highperformancestangs.com/gallery/data/521/P1010003.JPG
Remove the e brake cable from the retainer. Just grab it with pliers and pull.
http://www.highperformancestangs.com/gallery/data/521/P10100051.JPG
Remove the clip on the end of the e brake cable housing. A Small Screw driver will do the trick.
http://www.highperformancestangs.com/gallery/data/521/P1010006.JPG
Remove the bolt near the spring perch.
http://www.highperformancestangs.com/gallery/data/521/P10100071.JPG
Pull the cable out of the knuckle assembly.
http://www.highperformancestangs.com/gallery/data/521/P1010008.JPG
Remove the 2 brake caliper bolts 15mm
http://www.highperformancestangs.com/gallery/data/521/P10100091.JPG
Zip tie the calipers out of the way.
http://www.highperformancestangs.com/gallery/data/521/P10100101.JPG
Remove the tie rod end bolt 18mm.
http://www.highperformancestangs.com/gallery/data/521/P10100111.JPG
With the bolt still on loose. Tap it and the rod pop loose. Or you can buy a fancy tool that fords recommends if you are rich. LOL
http://www.highperformancestangs.com/gallery/data/521/P10100121.JPG
http://www.highperformancestangs.com/gallery/data/521/P10100131.JPG
If you never had your rotors off before you need to remove this clip on the stud.
http://www.highperformancestangs.com/gallery/data/521/P1010016.JPG
Remove the rotor.
http://www.highperformancestangs.com/gallery/data/521/P1010017.JPG
**IMPORTANT**
The knuckle has an upper and lower bolt.
The upper is a cam bolt.
Mark it with paint. The bolt must be reinstalled in the same position as it came out.
http://www.highperformancestangs.com/gallery/data/521/P10100151.JPG
Remove the nut and bolt 18mm.
http://www.highperformancestangs.com/gallery/data/521/P1010018.JPG
It is hard to get the half shaft boot past the shock.
Place a jack under the control arm to keep the spring from popping out and injuring you.
Then remove the lower shock mount bolt 18mm
http://www.highperformancestangs.com/gallery/data/521/P1010019.JPG
Near the differential I find it easy to place 2 screwdrivers between the tone ring and diff then gently pry the shaft loose. Be careful not to damage the diff seals. It will pop out easy.
If you just need to remove only the half shaft and not the hub tap on the end of the shaft with a hammer to get it free from the hub. It will slide out without without removing the the lower knuckle nut/bolt
If you are doing a hub and/or bearing replacement remove the lower knuckle nut/bolt 18mm.
Then just pull the shaft out with the knuckle attached.
http://www.highperformancestangs.com/gallery/data/521/P1010040.JPG
Half shaft was a little tight so a little pressure removed it from the hub but a BFH will work also.
http://www.highperformancestangs.com/gallery/data/521/P1010024.JPG
Press the wheel hubs out.
http://www.highperformancestangs.com/gallery/data/521/P1010025.JPG
Flip the knuckle over and remove the bearing retainer rings.
Press the old bearings out. They press out from the opposite side of the hubs.
http://www.highperformancestangs.com/gallery/data/521/P1010026.JPG
Press your new bearing in then install the retainer clips.
Flip the knuckle over and press the wheel hub in.
***Important***
Support the inner bearing race when pressing the hub in or you will ruin the new bearing.
You can see the race supported in the picture below on the bottom side of the knuckle.
http://www.highperformancestangs.com/gallery/data/521/P1010031.JPG
Re install the half shafts in reverse order from removal.
Axle nut torque is 240 ft-lbs on stock shafts.
Put the rear of the car on jack stands and remove the wheels.
Take the e brake off
35MM Axle socket from autozone.
Remove the nut.
http://www.highperformancestangs.com/gallery/data/521/P1010003.JPG
Remove the e brake cable from the retainer. Just grab it with pliers and pull.
http://www.highperformancestangs.com/gallery/data/521/P10100051.JPG
Remove the clip on the end of the e brake cable housing. A Small Screw driver will do the trick.
http://www.highperformancestangs.com/gallery/data/521/P1010006.JPG
Remove the bolt near the spring perch.
http://www.highperformancestangs.com/gallery/data/521/P10100071.JPG
Pull the cable out of the knuckle assembly.
http://www.highperformancestangs.com/gallery/data/521/P1010008.JPG
Remove the 2 brake caliper bolts 15mm
http://www.highperformancestangs.com/gallery/data/521/P10100091.JPG
Zip tie the calipers out of the way.
http://www.highperformancestangs.com/gallery/data/521/P10100101.JPG
Remove the tie rod end bolt 18mm.
http://www.highperformancestangs.com/gallery/data/521/P10100111.JPG
With the bolt still on loose. Tap it and the rod pop loose. Or you can buy a fancy tool that fords recommends if you are rich. LOL
http://www.highperformancestangs.com/gallery/data/521/P10100121.JPG
http://www.highperformancestangs.com/gallery/data/521/P10100131.JPG
If you never had your rotors off before you need to remove this clip on the stud.
http://www.highperformancestangs.com/gallery/data/521/P1010016.JPG
Remove the rotor.
http://www.highperformancestangs.com/gallery/data/521/P1010017.JPG
**IMPORTANT**
The knuckle has an upper and lower bolt.
The upper is a cam bolt.
Mark it with paint. The bolt must be reinstalled in the same position as it came out.
http://www.highperformancestangs.com/gallery/data/521/P10100151.JPG
Remove the nut and bolt 18mm.
http://www.highperformancestangs.com/gallery/data/521/P1010018.JPG
It is hard to get the half shaft boot past the shock.
Place a jack under the control arm to keep the spring from popping out and injuring you.
Then remove the lower shock mount bolt 18mm
http://www.highperformancestangs.com/gallery/data/521/P1010019.JPG
Near the differential I find it easy to place 2 screwdrivers between the tone ring and diff then gently pry the shaft loose. Be careful not to damage the diff seals. It will pop out easy.
If you just need to remove only the half shaft and not the hub tap on the end of the shaft with a hammer to get it free from the hub. It will slide out without without removing the the lower knuckle nut/bolt
If you are doing a hub and/or bearing replacement remove the lower knuckle nut/bolt 18mm.
Then just pull the shaft out with the knuckle attached.
http://www.highperformancestangs.com/gallery/data/521/P1010040.JPG
Half shaft was a little tight so a little pressure removed it from the hub but a BFH will work also.
http://www.highperformancestangs.com/gallery/data/521/P1010024.JPG
Press the wheel hubs out.
http://www.highperformancestangs.com/gallery/data/521/P1010025.JPG
Flip the knuckle over and remove the bearing retainer rings.
Press the old bearings out. They press out from the opposite side of the hubs.
http://www.highperformancestangs.com/gallery/data/521/P1010026.JPG
Press your new bearing in then install the retainer clips.
Flip the knuckle over and press the wheel hub in.
***Important***
Support the inner bearing race when pressing the hub in or you will ruin the new bearing.
You can see the race supported in the picture below on the bottom side of the knuckle.
http://www.highperformancestangs.com/gallery/data/521/P1010031.JPG
Re install the half shafts in reverse order from removal.
Axle nut torque is 240 ft-lbs on stock shafts.