Got the boot at speedworld

[silvrsvt]

with a shitty 1.96 60ft I went 12.05 @ 118mph no nitrous :twothumbsup: so I think I am going to try and put the cage in this week so I can go out again next week and try for that 11 second slip!

[SloSVO]

which cage you getting? MM or custom?

[az2k1]

the track sucked last night ,,,,but good run i ran after u with a 12.05 @116 w/2.0 60 ft ...

[BLK03SVT]

Nice!

[silvrsvt]

which cage you getting? MM or custom?

its a MM but its been customized. it bolts in where the back seat would be but instead I will have a rear seat delete with holes for the cage. Hopefully it will look good in there!

http://i290.photobucket.com/albums/ll265/silvrsvt/cage.jpg


the track sucked last night ,,,,but good run i ran after u with a 12.05 @116 w/2.0 60 ft ...

ya it sucked bad! I will be there next week but not until after work, around 7 or 8

[SloSVO]

get to work buddy!!! hehe...

[BurnTire]

Bolt in cross bar is not NHRA legal and will not pass tech.

[silvrsvt]

Bolt in cross bar is not NHRA legal and will not pass tech.

you are the 2nd person who has told me this. Last night I showed the picture to 2 different "tech's" at speedworld and they said it will pass just fine. Also the guy I bought it from used it at firebird and never had a problem..

Should I just have the cross bar welded in?

[BurnTire]

NHRA General Regulations: 4:10 Roll Bars
Crossbar and rear braces must be welded to main hoop.

The tubes must be welded together. That does not mean welding it to the tabs you have.

http://www.highperformancestangs.com/gallery/data/521/PA110030.JPG


If you plan to wrap your harnesses they must be boxed in.

http://www.highperformancestangs.com/gallery/data/521/PC310175.JPG

[SloSVO]

mike is going around posting the final list of people that are going on the 16th... he has you as going there...silvrsvt

[BUSTED]

:woot2: Cut That Mug Up Jack!

[silvrsvt]

spencer when we going to tackle this on? :beerchug:

[WildBill]

you are the 2nd person who has told me this. Last night I showed the picture to 2 different "tech's" at speedworld and they said it will pass just fine. Also the guy I bought it from used it at firebird and never had a problem..

Should I just have the cross bar welded in?

Bus driver is correct.
You have it welded in, it will be fine.

[BurnTire]

Bus driver is correct.
You have it welded in, it will be fine.

Pretty nice office for a bus driver :biglaugh:
http://www.transair.co.uk/images/posters/a319_320_321.jpg

[WildBill]

Pretty nice office for a bus driver :biglaugh:
http://www.transair.co.uk/images/posters/a319_320_321.jpg

Amazing how realistic the computer flight sims are now, huh?:laughing::laughing:

[BurnTire]

Amazing how realistic the computer flight sims are now, huh?:laughing::laughing: I wouldn't know as those games are for wanna be pilots. :Bucktooth:

[BUSTED]

spencer when we going to tackle this on? :beerchug:


I'll fix yours if you fix mine :yes:

[AZSonicSnake]

Bolt in cross bar is not NHRA legal and will not pass tech.

i'll be #3. was told this by a few tech officials.